step response造句

• Research on the cai of the step response of a second - order circuit
  二阶电路阶跃响应的计算机辅助教学研究
• Step response test
  脉冲响应试验
• Step response time
  阶跃响应时间
• Unit step response
  单位阶跃响应
• The direct method of process identification for computer control system by unit step response
  计算机控制系统对象模型辩识的单位阶跃响应直接法
• General methods of testing the performance of industrial process measurement and control instruments . step response
  工业自动化仪表通用试验方法.阶跃响应
• Based on the test system of unloading valve , the step response method is used to acquire the step response curve of this system
  以卸荷阀性能测试系统作为研究对象，利用阶跃响应法获得系统的阶跃响应曲线并求得了系统的传递函数。
• Based on pole assignment , the step response of suspension system with active control is simulated and compared to that with passive control
  通过极点配置法对采用主动控制的履带车辆悬挂系统进行仿真，并将仿真结果与采用被动悬挂系统相比较。
• The result indicated that the system had good step response and tracking performance and met the requirement of quantitative control of cycling power
  结果表明所设计控制系统阶跃响应性能良好,并有较好的跟踪性能,能够满足训练者运动定量控制的要求。
• It was found that the start - up and step response time of pem fuel cell was in the order of seconds , which was similar to the simulation results of most presently used models
  结果表明：电池的启动时间和阶跃响应时间均为秒的数量级，与大多数模模拟的结果相一致。
• The time domain property test contains static property test and step response test . depended on the result of the test , the transfer function of the system was deduced
  时域特性测试包括致动器静态特性测试和阶跃响应特性测试，并根据测试结果分析了被控对象的传递函数。
• For iir , after researching pulse response method , step response method , bilinear transform method , direct design method , it is found that iir is unsatisfactory
  对iir的脉冲响应不变法、阶跃响应不变法、双线性变换法和直接设计法进行研究，得出iir难以满足要求的结论。
• I contrast this method with pid control method , and then i see that as far as the step response is concerned , my approach is not much advantageous than pid control method
  并将它与传统的pid控制对比，发现单单就阶跃响应来看，模糊自适应控制与常规pid控制比较无优势可言。
• For the feedforward controller design , zero error characteristic of the step response of system with zero phase error tracking controller ( zpetc ) is proved and its application is studied
  对于前馈控制器设计，证明了零相位误差跟踪算法在阶跃输入下的无差性并研究了该特性的应用。
• The temperature of resistor - furnace is a one - order inertial pure lagging system . by making computer simulation with matlab and adjusting kp , we obtain a satisfied step response curve
  电阻炉炉温为一阶惯性纯滞后系统，通过matlab进行计算机仿真，调节kp的值，可得到较为理想的阶跃响应曲线。
• 5 . the control systems of the heater are designed by the adaptive fuzzy neuron control arithmetic . the step response curve is got . the results show their nice performances
  针对实验室电加热炉系统，使用自适应模糊单神经元控制算法进行控制系统的设计，得出阶跃响应曲线，取得了满意的控制效果。
• At first , the algorithms for " nose - to - nose " calibration technology acquiring the parameters are introduced , including the algorithms for acquiring the impulse response , the step response , the rise time , the amplitude response and the phase response
  首先,介绍了“ nose - to - nose ”校准技术获取示波器冲激响应、阶跃响应、过渡时间、幅频特性和相频特性的各种算法。
• The system ' s transfer function is acquired according to the step response curve . the influence of the system ' s pressure balance time affected by the steady and unstable state ' s increasing is discussed , the conclusion has practice meaning
  深入客观地探讨了不同的加压速率利加压幅值以及分阶段加压对卸荷阀性能测试系统压力平衡时间的影响，获得了有实践指导意义的结果。
• Firstly the pwm implementation of relay is given . in succession the characteristic of extruder barrel is obtained by measuring their step response . at last the implementation of pid and fuzzy control are studied in detail and the results of the experiment are presented
  首先对料筒特性进行了测试研究，介绍了继电器pwm控制的实现方法，然后分别进行了积分分离pid及模糊变系数pid控制策略的研究。
• A on - identify model of proportional valve pressure controlled system was established though analyzing the configuration of dbetr type proportional pressure relief valve firstly , and then using classical step response method to identify system parameter , a practicable system simple model was deduced at last
  摘要从dbetr型比例压力溢流阀结构出发，先建立比例阀控制压力系统的待辨识模型，再采用经典的阶跃响应法辨识系统参数，得到工程上适用的系统简化模型。